s0143, rev.03. (web) 2013-05-17 trpeg1-g mr cwdm absolute maximum ratings parameter symbol minimum maximum units storage temperature range t st - 40 + 85 c operating case temperature 1 commercial t op - 5 + 70 c extended - 5 + 85 supply voltage v cc 0 + 4.5 v input voltage v in 0 v cc v 1 measured on top side of sfp module at the front center vent hole of the cage. pb the trpeg1-g mr cwdm sfp series of multi-rate fber optic transceivers with integrated digital diagnostics monitoring functionality provide a quick and reliable interface for 1000base-lx gigabit ethernet and 1.062gbd fibre channel applications. the transceivers are designed to support data rates ranging from 1.25gb/s down to 125mb/s. diagnostics monitoring functionality (alarm and warning features) is integrated into the design via an i 2 c serial interface per the multi-source agreement (msa) sff-8472, rev. 9.4. there are eighteen center wavelengths available, from 1271nm to 1611nm. two optical link power budget options are ofered, yx (22db minimum) and zx (24db minimum). they correspond to transmission distances of 62km and 70km respectively (assuming a total connector/splice/ cwdm mux and demux loss of 4.5db, allocated system penalty of 2db and fber loss of 0.25db/km). all modules satisfy class i laser safety requirements in accordance with the u.s. fda/cdrh and international iec-60825 standards. the trpeg1-g mr cwdm transceivers connect to standard 20-pad sfp connectors for hot plug capability. this allows the system designer to make confguration changes or maintenance by simply plugging in diferent types of transceivers without removing the power supply from the host system. the transceivers have colored bail-type latches, which ofer an easy and convenient way to release the modules. the latch is compliant with the sfp msa. the transmitter and receiver data interfaces are ac coupled internally. lv- ttl transmitter disable control input and loss of signal output interfaces are also provided. the transceivers operate from a single +3.3v power supply over an operating case temperature range of -5c to +70c (commercial) or -5c to +85c (extended). the housing is made of metal for emi immunity. product description ? eighteen (18) wavelength cwdm transceivers ? lead free design & rohs compliant ? compliant to sfp msa ? compatible with ieee 802.3z gigabit ethernet 1000base-lx pmd specifcations ? compatible with 1.062gbd fibre channel 100-sm- lc-l fc-pi standards ? digital diagnostics through serial interface ? internal calibration for digital diagnostics ? minimum optical link power budgets of 22db and 24db to support 62km and 70km ? eye safe (class i laser safety) ? duplex lc optical interface ? loss of signal output & tx disable input ? hot-pluggable features multi-rate gigabit ethernet & fibrechannel sfp cwdm transceivers with digital diagnostics
oplink communications, inc s0143, rev.03. (web) 2013-05-17 2 oplink communications, inc. this product complies with 21 cfr 1040.10 and 1040.11 meets class i laser safety requirements laser safety : all transceivers are class i laser products per fda/cdrh and iec-60825 stan - dards. they must be operated under specifed operating conditions. transmitter performance characteristics trpeg1-g mr cwdm (over operating case temperature. v cc = 3.13 to 3.47v) parameter symbol minimum typical maximum units operating data rate b 125 - 1250 mb/s average optical output power 1 yx p o - 2.0 - + 3.0 dbm zx 0 - + 5.0 center wavelength see ordering information table nm wavelength deviation ? c - 6.5 c c + 6.5 nm spectral width (-20db) ? - - 1.0 nm side mode suppression ratio smsr 30 - - db extinction ratio er 9 - - db deterministic jitter d j - - 80 ps total jitter t j - - 227 ps optical rise/fall time (20% to 80%) t r ,t f - - 0.32 ns relative intensity noise rin - - - 120 db/hz dispersion penalty 2 - - - 1.5 db transmitter output eye compliant with ieee 802.3z & fc-pi eye mask 1 measured average power coupled into single mode fber. 2 specifed at 1360ps/nm (yx) and 1540ps/nm (zx) dispersion, which corresponds to the approximate worst-case dispersion for 62km and 70km g.652 fber over the wavelength range of 1264.5 to 1617.5nm. receiver performance characteristics parameter symbol minimum typical maximum units operating data rate b 125 - 1250 mb/s receiver sensitivity (10 -12 ber) 1 p min - 24.0 - - dbm maximum input optical power (10 -12 ber) 1 p max - 3.0 - - dbm los thresholds increasing light input p los+ - - - 24.0 dbm decreasing light input p los- - 35.0 - - los timing delay increasing light input t_loss_of - - 100 fs decreasing light input t_loss_on - - 100 los hysteresis - 0.5 1.5 - db deterministic jitter d j - - 80 ps total jitter t j - - 266 ps wavelength of operation 1260 - 1620 nm optical return loss orl 12 - - db electrical 3db upper cutof frequency - - - 1500 mhz 1 measured with 2 7 -1 prbs at 125mb/s, 1062.5mb/s and 1250mb/s. (over operating case temperature. v cc = 3.13 to 3.47v)
3 trpeg1-g mr cwdm oplink communications, inc s0143, rev.03. (web) 2013-05-17 electrical pad layout host board connector pad layout bottom of board (as viewed thru top of board) top of board to ward bezel to ward asi c 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 t x gnd t d- ( tx d ata in-) t d+ ( tx d ata in+) t x gnd v cc tx v ccrx rx gn d rd+ (rx d at a out+) rd- (rx d at a out- ) rx gn d 1 2 3 4 5 6 7 8 9 10 tx gnd tx f aul t tx disabl e mod_def(2) mod_def(1) mod_def(0) no c onnect ion lo s rx gnd rx gnd transmitter performance characteristics parameter symbol minimum typical maximum units input voltage swing (td+ & td-) 1 v pp-diff 0.5 - 2.4 v input high voltage (tx disable) 2 v ih 2.0 - v cc v input low voltage (tx disable) 2 v il 0 - 0.8 v output high voltage (tx fault) 3 v oh 2.0 - v cc + 0.3 v output low voltage (tx fault) 3 v ol 0 - 0.8 v 1 diferential peak-to-peak voltage. 2 there is an internal 4.7 to 10k pull-up resistor to vcct. 3 open collector compatible, 4.7 to 10k pull-up resistor to vcc (host supply voltage). mod_def(0) pin 6 mod_def(1) pin 5 mod_def(2) pin 4 interpretation by host ttl low scl sda serial module defnition protocol module definition (over operating case temperature. v cc = 3.13 to 3.47v) parameter symbol minimum typical maximum units output voltage swing (rd+ & rd-) 1 v pp-diff 0.6 - 2.0 v output high voltage (los) 2 v oh v cc - 0.3 - v cc + 0.3 v output low voltage (los) 2 v ol 0 - 0.5 v 1 diferential peak-to-peak voltage across external 100 load. 2 open collector compatible, 4.7 to 10k pull-up resistor to vcc (host supply voltage). parameter symbol minimum typical maximum units supply voltage v cc 3.13 3.30 3.47 v supply current i cc - 200 300 ma (over operating case temperature. v cc = 3.13 to 3.47v) electrical power supply characteristics (over operating case temperature. v cc = 3.13 to 3.47v) receiver electrical characteristics
4 trpeg1-g mr cwdm oplink communications, inc s0143, rev.03. (web) 2013-05-17 application notes electrical interface: all signal interfaces are compliant with the sfp msa specifcation. the high speed data interface is diferential ac-coupled internally with 1ff and can be directly connected to a 3.3v serdes ic. all low speed control and sense output signals are open collector ttl compatible and should be pulled up with a 4.7 - 10k resistor on the host board. loss of signal (los): the loss of signal circuit monitors the level of the incoming optical signal and generates a logic high when an insufcient photocurrent is produced. tx_fault: the output indicates low when the transmitter is operating normally, and high with a laser fault including laser end-of-life. tx fault is an open collector/drain output that should be pulled up with a 4.7 - 10k resistor on the host board. tx fault is latched per sfp msa. tx_disable: when the tx disable pin is at logic high, the transmitter optical output is disabled (less than -45dbm). serial identifcation and monitoring: the module defnition of sfp is indicated by the three module definition pins, mod_def(0), mod_def(1) and mod_def(2). upon power up, mod_def(1:2) appear as nc (no connection), and mod_def(0) is ttl low. when the host system detects this condition, it activates the serial protocol (standard two-wire i 2 c serial interface) and generates the serial clock signal (scl). the positive edge clocks data into the eeprom segments of the sfp that are not write protected, and the negative edge clocks data from the sfp. the serial data signal (sda) is for serial data transfer. the host uses sda in conjunction with scl to mark the startand end of serial protocol activation. the supported monitoring functions are internal temperature, supply voltage, bias current, transmitter power, average receiver signal, all alarms and warnings and software monitoring of tx fault/los. the device is internally calibrated. the data transfer protocol and the details of the mandatory and vendor specifc data structures are defned in the sfpmsa, and sff-8472, rev. 9.4. power supply and grounding: the power supply line should be well-fltered. all 0.1ff power supply bypass capacitors should be as close to the transceiver module as possible. tx da ta in + 1h co il or fe rr it e bead (<0.2 series resistance) 0. 1 tx da ta in - tx di sa bl e 0.1 + 10 0. 1 + 10 to 50 load 3. 3v rx da ta ou t+ rx da ta ou t- mo d_ de f( 0) mod_ de f( 1) mod_ de f( 2) lo s to 50 load tx fa ul t vcc 3.3v vc c 50 line 50 line 50 line 50 line r r r r r 8 5 4 6 2 18 19 3 15 16 13 12 1, 9,10,11,14,17,20 example of sfp host board schematic sfp r: 4.7 to 10k cap values in f
5 trpeg1-g mr cwdm oplink communications, inc s0143, rev.03. (web) 2013-05-17 mechanical package dimensions in inches [mm] default tolerances: .xxx = .005, .xx = .01 ordering information oplink part number operating temperature nominal wavelength (nm) latch color 22db link budge (62km distance) 1 24db link budget (70km distance) 1 trpeg1hyxc000l0g trpeg1kzxc000l0g - 5c to +70c commercial 1271 light violet trpeg1hyxc000k0g trpeg1kzxc000k0g - 5c to +70c commercial 1291 sky blue trpeg1hyxc000j0g trpeg1kzxc000j0g - 5c to +70c commercial 1311 dark green trpeg1hyxc000h0g trpeg1kzxc000h0g - 5c to +70c commercial 1331 magenta trpeg1hyxc000g0g trpeg1kzxc000g0g - 5c to +70c commercial 1351 pink trpeg1hyxc000f0g trpeg1kzxc000f0g - 5c to +70c commercial 1371 beige trpeg1hyxc000d0g trpeg1kzxc000d0g - 5c to +70c commercial 1391 white trpeg1hyxc000c0g trpeg1kzxc000c0g - 5c to +70c commercial 1411 silver trpeg1hyxc000b0g trpeg1kzxc000b0g - 5c to +70c commercial 1431 black trpeg1hyxc000a0g trpeg1kzxc000a0g - 5c to +70c commercial 1451 lime trpeg1hyxc00010g trpeg1kzxc00010g - 5c to +70c commercial 1471 gray TRPEG1HYXC00020G trpeg1kzxc00020g - 5c to +70c commercial 1491 violet trpeg1hyxc00030g trpeg1kzxc00030g - 5c to +70c commercial 1511 blue trpeg1hyxc00040g trpeg1kzxc00040g - 5c to +70c commercial 1531 green trpeg1hyxc00050g trpeg1kzxc00050g - 5c to +70c commercial 1551 yellow trpeg1hyxc00060g trpeg1kzxc00060g - 5c to +70c commercial 1571 orange trpeg1hyxc00070g trpeg1kzxc00070g - 5c to +70c commercial 1591 red trpeg1hyxc00080g trpeg1kzxc00080g - 5c to +70c commercial 1611 brown
oplink communications, inc. reserves the right to make changes in equipment design or specifcations without notice. information supplied by oplink commu - nications, inc. is believed to be accurate and reliable. however, no responsibility is assumed by oplink communications, inc. for its use nor for any infringements of third parties, which may result from its use. no license is granted by implication or otherwise under any patent right of oplink communications, inc. ? 2013, oplink communications, inc. 6 trpeg1-g mr cwdm 46335 landing pkwy fremont, ca 94538 tel: (510) 933-7200 fax: (510) 933-7300 email: sales@oplink.com ? www.oplink.com s0143, rev.03. (web) 2013-05-17 oplink part number operating temperature nominal wavelength (nm) latch color 22db link budge (62km distance) 1 24db link budget (70km distance) 1 trpeg1hyxe000l0g trpeg1kzxe000l0g - 5c to +85c extended 1271 light violet trpeg1hyxe000k0g trpeg1kzxe000k0g - 5c to +85c extended 1291 sky blue trpeg1hyxe000j0g trpeg1kzxe000j0g - 5c to +85c extended 1311 dark green trpeg1hyxe000h0g trpeg1kzxe000h0g - 5c to +85c extended 1331 magenta trpeg1hyxe000g0g trpeg1kzxe000g0g - 5c to +85c extended 1351 pink trpeg1hyxe000f0g trpeg1kzxe000f0g - 5c to +85c extended 1371 beige trpeg1hyxe000d0g trpeg1kzxe000d0g - 5c to +85c extended 1391 white trpeg1hyxe000c0g trpeg1kzxe000c0g - 5c to +85c extended 1411 silver trpeg1hyxe000b0g trpeg1kzxe000b0g - 5c to +85c extended 1431 black trpeg1hyxe000a0g trpeg1kzxe000a0g - 5c to +85c extended 1451 lime trpeg1hyxe00010g trpeg1kzxe00010g - 5c to +85c extended 1471 gray trpeg1hyxe00020g trpeg1kzxe00020g - 5c to +85c extended 1491 violet trpeg1hyxe00030g trpeg1kzxe00030g - 5c to +85c extended 1511 blue trpeg1hyxe00040g trpeg1kzxe00040g - 5c to +85c extended 1531 green trpeg1hyxe00050g trpeg1kzxe00050g - 5c to +85c extended 1551 yellow trpeg1hyxe00060g trpeg1kzxe00060g - 5c to +85c extended 1571 orange trpeg1hyxe00070g trpeg1kzxe00070g - 5c to +85c extended 1591 red trpeg1hyxe00080g trpeg1kzxe00080g - 5c to +85c extended 1611 brown 1 the indicated transmission distance is for guidelines only, not guaranteed. it assumes a total connector/splice/cwdm mux and demux loss of 4.5db, allocated system penalty of 2db and fber loss of 0.25db/km. longer distances can be supported if the optical link power budget is satisfed.
|
